How to Configure RIP Version 2 (RIPv2) on Cisco Router in GNS3 | SYSNETTECH Solutions



How to Configure RIP Version 2 (RIPv2) on Cisco Router in GNS3 | SYSNETTECH Solutions ► Article ► https://goo.gl/XR6Tla Read More ⬇️

✅ S U B S C R I B E ► http://goo.gl/8d0iG9

This video shows you how to configure RIP Version 2 (RIPv2) on Cisco Routers using the GNS3 network simulator program on Windows 10.

To configure RIP Version 2 (RIPv2) on Cisco Routers on GNS3:

Step 1: If you have not installed GNS3 on Windows, Linux or even MacOS before, please refer to the following videos.

Windows ➦ https://www.youtube.com/watch?v=yuJ5qXFpr7Q
Linux / Ubuntu ➦ https://www.youtube.com/watch?v=b6A2peSovLU
MacOS ➦ https://www.youtube.com/watch?v=MWStTRpwqBY

Step 2: Once you have done the GNS3 setup, you need the Cisco Router IOS images you will use on the GNS3. To download the most appropriate Cisco Router images for GNS3, please click the reference link below.

➦ https://www.sysnettechsolutions.com/en/gns3/gns3-supported-ios-images-download/

Step 3: After downloading the Cisco Router IOS image for GNS3, add the downloaded IOS image to GNS3. If you do not know how to add the Cisco Router image on GNS3, the following reference link will help you.

➦ https://www.sysnettechsolutions.com/en/gns3/adding-cisco-ios-to-gns3/

Step 4: After adding the Cisco Router to GNS3, drag and drop two Cisco Routers to the workspace.

Step 5: Also, add two Cisco Switches to the workspace from the GNS3 tools.

Step 6: Using VPCS on GNS3 will give you performance. Add four VPCS to the workspace. If you do not know how to configure VPCS, the video will help you. You can also get more information from the reference link below.

➦ https://www.sysnettechsolutions.com/en/gns3/use-vpcs-in-gns3-configure-vpcs-on-gns3/

Step 7: Before configuring RIP Version 2 on Cisco Routers in GNS3, specify two different network addresses. For example;

A) 192.168.5.0/25
B) 192.168.5.128/25

Step 8: Connect the Cisco Routers with the Serial Interface. Connect the Cisco Switches to the Ethernet ports of Cisco Routers. Finally, connect the VPCS to the Switches and proceed to the next step.

Step 9: Assign IP addresses to the Serial and Ethernet interfaces of Cisco Routers and enable ports with no shutdown command.

➦ no shutdown

Step 10: Finally, configure the IP of the VPCS.

Step 11: Note the subnet mask while configuring VPCS.

Step 12: Before configuring RIP Version 2, check the connection by pinging the Cisco Router’s interfaces from the VPCS.

Step 13: In GNS3, two different networks cannot communicate with each other without configuring RIP V2 on Cisco Routers.

Step 14: To configure RIP V2 on Cisco Routers, first, open the CLI command prompt on the Router named R1 and execute the following commands.

R1# conf t
R1#(config)# router rip
R1#(config-router)# version 2
R1#(config-router)# network 10.1.1.0
R1#(config-router)# 192.168.5.0
R1#(config-router)# end

Step 15: To configure RIP V2 on Cisco Router R2, perform the following commands.

R2# conf t
R2#(config)# router rip
R2#(config-router)# version 2
R2#(config-router)# network 10.1.1.0
R2#(config-router)# 192.168.5.128
R2#(config-router)# end

Step 16: After configuring RIP Version 2 on Cisco Routers using GNS3, check out the RIPV2 configuration using show commands.

RIP Routing Verification Commands:

➦ show ip protocols
➦ show ip route
➦ show ip interface brief
➦ show ip rip database
➦ debug ip rip

Step 17: Watch the video for the rest of the process.

Step 18: Don’t forget to subscribe to our YouTube channel for more videos on Cisco training with GNS3!

➦ http://goo.gl/8d0iG9

────BEST PRODUCT FOR CISCO TRAINING──────

✅ Buy ► http://bit.ly/CiscoNetworkingEssentials

──────────── RELATED VIDEOS ──────────────

➊ How to Integrate VMware Workstation with GNS3?
➦ https://www.youtube.com/watch?v=SwE9VaZ7lXQ

➋ How to Configure RIP on Cisco Router in GNS3
➦ https://www.youtube.com/watch?v=839dk8lYhFU

➌ How to Configure Cloud in GNS3
➦ https://www.youtube.com/watch?v=DVokiwWzlxk

➍ How to Configure OSPF on Cisco Router in GNS3
➦ https://www.youtube.com/watch?v=gFMvgpDSzlI

➎ How to Configure EIGRP on Cisco Router in GNS3
➦ https://www.youtube.com/watch?v=rJC3UERvdnQ

───────────────FOLLOW US───────────────────

✔ Facebook
➦ https://www.facebook.com/SysnettechSolutions/

✔ Twitter
➦ https://twitter.com/SysnettechS/

✔ Pinterest
➦ https://www.pinterest.com/SysnettechS/

✔ Instagram
➦ https://www.instagram.com/sysnettech_solutions/

✔ LinkedIn
➦ https://linkedin.com/in/tolqabaqci/

███████████████████████████████████████████

source

Mourad ELGORMA

Mourad ELGORMA

Fondateur de summarynetworks, passionné des nouvelles technologies et des métiers de Réseautique , Master en réseaux et système de télécommunications. ,j’ai affaire à Pascal, Delphi, Java, MATLAB, php …Connaissance du protocole TCP / IP, des applications Ethernet, des WLAN …Planification, installation et dépannage de problèmes de réseau informatique……Installez, configurez et dépannez les périphériques Cisco IOS. Surveillez les performances du réseau et isolez les défaillances du réseau. VLANs, protocoles de routage (RIPv2, EIGRP, OSPF.)…..Manipuler des systèmes embarqués (matériel et logiciel ex: Beaglebone Black)…Linux (Ubuntu, kali, serveur Mandriva Fedora, …). Microsoft (Windows, Windows Server 2003). ……Paquet tracer, GNS3, VMware Workstation, Virtual Box, Filezilla (client / serveur), EasyPhp, serveur Wamp,Le système de gestion WORDPRESS………Installation des caméras de surveillance ( technologie hikvision DVR………..). ,

9 réflexions sur “How to Configure RIP Version 2 (RIPv2) on Cisco Router in GNS3 | SYSNETTECH Solutions

Laisser un commentaire